组合导航非等间隔联合滤波

组合导航系统中各种导航设备数据更新频率的不同会导致联合滤波算法无法在每个计算周期都融合局部滤波器的信息，从而导致信息丢失和引入人为误差。为此提出了一种可以最优融合不同测量周期信息的非等间隔联合滤波算法，并且给出了算法的最优性证明。这种算法通过设定不同的计算周期和融合周期，实现了非等间隔测量信息的最优融合。     

翼型大攻角状态下表面吸气驻涡增升的数值模拟实验

用数值模拟方法给出了翼型大攻角状态表面吸气后绕翼型流动的某些新现象并对流场的特性进行了机理性研究,其中包括吸气对翼型背风面分离涡的驻涡增升作用;吸气孔位置对流场的影响;不同吸气强度以及间歇式吸气的增升效应。数值模拟的出发方程为N-S方程,差分格式为Beam-Warming格式。数值实验表明:(1)吸气可有效地提高翼型大攻角状态下的升力;(2)在一定吸气强度下吸气可使翼型背风面上涡的非定常脱落现象消失从而起到驻涡作用;(3)吸气孔位置在翼面的中部附近增升效果较好;(4)在一定范围内吸气强度越强其升力越高;(5)间歇式吸气也可提高平均升力,但引起升力的波动。     

On the relationship between the work of adhesion and the critical shear stress for the onset of flow instabilities

The relationship between the critical shear stress for the onset of flow instabilities and the work of adhesion at the interface has been evaluated experimentally for a series of polyolefins on several steels, brasses, and coated steels. The critical shear stress was considerably affected by the chemical nature of the die. Low-surface-energy materials were found to produce smooth extrudates presumably by inducing slippage at the wall. Steel, tungsten carbide, and brass surfaces promoted sharkskin defect at shear stresses above the first critical shear stress. A linear relationship between the critical shear stress and the work of adhesion was found to be valid for values of work of adhesion smaller than approximately 30 mN/m. This indicates that slippage occurs due to a breakdown of the adhesion at the interface. For values of work of adhesion greater than approximately 30 mN/m a stronger interaction at the interface may induce a cohesive failure at the interface and subsequently, extrudate distortions.     

区段混合能的偏微分方程

结构力学与最优控制模拟关系的共同基础就是分析力学，表明在结构力学与最优控制理论的架构内也应有分析力学的整套理论。传统分析力学总是考虑连续时间、同时的状态、不变维数的体系。并且物性为即时响应的。但结构力学有限元要考虑离散坐标、不同坐标状态、而且变动维数、时滞的体系。根据区段变形能只与其两端位移有关，就可通过数学分析得到Lagrange括号与Poisson括号等内容。区段变形能就是作用量，满足Hamilton-Jacobi方程。但还有区段混合能的表示，本文证明它满足雷同的偏微分方程。它们在离散体系时还有偏差分方程。本文进一步给出了其与Riccati方程的关系。     

山地输电线动刚度计算及模态分析

为了揭示地形变化对连续档输电线动态特性的影响，本文提出了基于任意高差角的动刚度理论．首先将单档导线视为连续档导线的子结构，构建了两悬挂点不等高的单档导线振动方程，并在该理论方程中引入了二次项，能够考虑重力沿弦向分量的影响，推导出绝缘子串绕其悬挂点转动的动刚度计算方法，通过动刚度理论研究连续档导线横向振动模态和频率，并应用有限元软件ABAQUS 验证理论模态和频率公式的准确性．所得结果表明，动刚度的计算方法具有较高的精度，理论模态与有限元输出结果吻合较好，同时获得的频率和模态可为山地高压输电线路防舞技术的研究提供依据．     

Rotating bunsen flames as solutions of the Kuramoto-Sivashinsky equation

Steadily rotating solutions of the Kuramoto-Sivashinsky equationu _t + ² u++¦u¦ ² =c ² are studied. These solutions bifurcate from the steady radial solution of the above equation. For large values ofc and angular velocities such thatN¦¦<2c<(N+1)¦¦, we show that there exists a 2N-1 family of bifurcating solutions. The proof is based on a certain generic transversality assumption. A computer-assisted proof of this assumption is given for 1N10.     

Correlation of swirl number for a radial-type swirl generator

An experimental investigation was undertaken to derive a new correlation for the swirl number of a radial-type swirl generator under various Reynolds numbers and various vane angle conditions. A radial-type swirl generator with 16 rotary guide vanes was used to generate an annular swirling jet flow. The Reynolds numbers ranged from 60 to 6000, and the vane angles from 0° to 56°. Quantitative measurements for the velocities were made by using an optical method of laser-Doppler anemometry (LDA). Three-component velocity profiles of axial, radial, and azimuthal components at the swirling jet exit were measured for various flow conditions. A flow visualization method using smoke-wire and still photography was also applied to observe the flow patterns of the recirculation region behind the circular bluff body. Under low Reynolds number conditions, the swirl strength was found to be strongly dependent on the Reynolds number as well as on the guide vane angle. Based on the experimental results, a modified swirl number S is derived to characterize the swirling flow, which is useful for the design of a swirl generator.     

X型热膜探头的标定

本文研究了Ｘ型热膜探头的两种主要标定方法，有效角法和多速度偏航法，对两种方法使用时可能引入的误差进行了讨论，并对给定的同一流场用不同方法进行了计算。     

微重时卧圆柱内静液面方程与数值计算

由力学平衡方程导出了微重时卧圆柱内静液面方程，推出了边界接触角条件，使用Ｒｕｎｇｅ Ｋｕｔａ法在计算机上得出了数值结果，绘出了静液面形状，并对结果进行了分析．     

岩石节理粗糙面的分形几何特性与剪切强度关系的实验研究

自然形成的岩石节理面的表面形状具有分形特性，利用分形理论来描述岩石节理的粗糙特性，并确立与岩石节理面的剪切力学特性间的关系对于指导岩体工程设计，和管理具有重要一研究利用开发设计的三维激光测距仪在精确测定岩石节理面的表面形状４ 基础上，依据变量图法建立了 岩石节理面的